Tuesday, June 22, 2010

Closing down and a discovery

A few days ago while delivering the mail to one of my businesses, I spied in a pick up there a couple of old relics. One was a mid 60ish Honda CB72 or CB77, not really sure which. It was in a bit of a state but recoginizeable. The other was a BSA which was in a bad way was well. From the looks of it it could have been either a C15 or a B40 as it had a distributor on it  and was from the early to mid 60s before Amelia the Starfire was made. Haven't had a chance to talk to Andy, the owner, to find out about the BSA.

The closure was of a bike knackers warehouse in the local area. I heard through word of mouth that the place was closing as the building had been sold so everything had to go.

Too bad I didn't have the money as there may have been a few things such as helmets or whatever to be had at a good price. I also didn't find out abou tthis until after the fact so it was too late.

The last time I was there was about a month or so back to check on something trivial. As they had mainly bikes from the Orient there, I didn't even bother about parts for Amelia or Vicky. But I did see a couple of Yamahas and Hondas that were from the time I started riding, back in the days of the dinosaurs, the 70s.

Oh well, there's still the bike shows such as New Ulm and eBay to get stuff.

Tuesday, June 8, 2010

A rainy day

Today started out quite wet and it looks like it'll end that way too. As I was off today from the salt mines, I didn't get wet which is always a good thing.

But I did go into the shed for a bit. As I have run out of wet-n-dry paper to sand the frame some more and to get rid of any gunge I decided to do sommit else that didn't require any sanding.

I attacked the rear wheel, specifically the hub and bearings. Started out, after getting the wheel on the bench, I went to take off the plate that the speedo drive sits on while in the swing arm. This is an easy thing to do, just unscrew it from the hub.

This is even easier when you turn it in the right direction, which in this case is to the right as it is a reverse thread. However Muggins here knew to do this but insisted on turning it to the left as per normal threading. It took a minute or two before I realized what a daft twit I am and then proceeded to do it right.

The plate came off, as well as the sandwich of three large flat washer type seals, one of which is made of felt. Very high tech these classsic machines!

Then it was a couple of quick blows using a small lump hammer and suitable drifts and both the wheel bearings came out.

Even though I used drifts to get them out without damaging the races, I'm still gonna replace them as "Great Britain" is stamped into the outer edge of the bearings which tells me that they are the originals and even though still may be servicable, they need to be updated.

Unfortunately there isn't a local BSA agent nearabouts, so that means a trip down to the local bearing distributor for the replacement items. As they cost about $10 or about a Fiver each in hometown money, it's a good deal.

Later on, I'll put it all back together and the wheel will be good as new, especially after cleaning the rim up and replacing the tire. This also will apply to the front as well when I get to that one.

And seeing how I've gone through the experience with Amelia, I'll be in familiar territory and know what I'm doing.

Until next time.....toodle pip!     

Monday, May 31, 2010

A frame up....get it???

Today to take a wee break after cutting the grass I went into the shed for a spot of work on Vicky.

OK it was just to take a few pictures of her for future reference when putting her back together at a later date.

Until recently I had the frame balancing on top of a milk crate which isn't a great platform to say the least, while on the bench.

 Then I hit upon using the overhead beams liike I had before when the front end was out of Amelia.

But this time it was A LOT easier to deal with as there wasn't all the bits and bobs there such as a motor, etc. Just strung some tie-downs up and secured the frame to the tie-downs. Now the frame is at eye level. Brilliant!



Still have some sanding to do on the frame before priming and then painting and this is the perect height to do it. Only thing is any overspray containment but I think that I can cobble together a temporary paintbooth.

A good thing about having the frame at this height is that I can check the bottom of the frame easier and when I did, I found that there is still a little bit of gunge underneath. So more work with the wet-n-dry paper and a good going over for any pitting or dings that may need to be filled in.

If so, that'll  be next on the agenda after the sanding.

It never ends does it??

But before I forget, I got the rattle can out and put some spray primer on the oil tank.


Did notice a slight crease in the tank after spraying it, hopefully it won't be too noticeable after the top coat and clearcoat go on.

Sunday, May 23, 2010

RIP Pooh


Cliff "Pooh" Gingell



Yesterday I lost a friend by the name of Pooh.

Cliff Gingell or Pooh as he was known was a bloke I knew from one of the forums I belong to. A few months back he started to complain of severe stomach problems and when he went to the doctor to get checked out, they "didn't know what was wrong".

This went on for quite a while until just recently when one doctor finally diagnosed him having pancreatic cancer.

Of course this was a terrible thing to find out, made even worse in my opinion by doctors who "couldn't find the problem" either through sheer stupidity or laziness.

Either way, he had limited time left even though these doctors gave him 8-9 months to go. Anyone with pancreatic cancer usally lasts for about 90 days and Pooh was nearly there when the diagnosis was made.

I met Pooh two years ago when I made a trip home. He lived in Daventry which is about 30 miles from the village I lived in.

Through correspondence on the forum Pooh offered me the loan of one of his BMWs for the time I was gonna be there and I took him up on it.

The BMW was a K100 model, this one in fact:



I used this bike to go to Scotland and to ride around the local Banbury area while home. A trip to London to the Ace Cafe was cancelled due to heavy rain that day. 

Pooh didn't know me from Adam at the time, but he trusted me with his bike. He and his wife Sue had me as a guest for the day prior to getting the bike. Pooh picked me up at home, we drove back to Daventry and spent the day talking. They also made a curry dinner for us all to eat.

There was one thing that Pooh did that made him stand out and that was his low tolerance for racial bigotry. Several times on the foum when some character used racial comments, Pooh would let the person know in no uncertain terms that it was not to be tolerated.

Pooh was one of the good 'uns and will be greatly missed. The world needs more bikers like him.

RIP Pooh. 

Pooh was buried today, June 7, 2010. From what I hear, there was a good turn out of members from the ClassicBikeForum who came from various parts of England to pay their respects. Rest easy mate and I'll have a dram in your memory.